Skip to content
Serving Brooklyn and nearby cities Mon–Fri: 8 AM–8 PM · Requests accepted 24/7 · (912) 881-8281

Fireplace & Damper Repair in Brooklyn

Serving Brooklyn and nearby cities.

Tell us what’s going on

Prefer to talk? (912) 881-8281

The short answer

You need fireplace and damper repair when smoke spills into the room, the damper sticks or won't seal, firebrick or mortar is crumbling, or water shows up in the firebox after rain. EliteFlue's certified technicians inspect to the NFPA 211 standard, repair the actual cause, and protect your home with drop cloths and HEPA vacuums.

A fireplace has more working parts than most people realize. The damper has to open fully when you light a fire and seal tightly when you don't. The firebrick and mortar take direct heat every time you burn. The smoke chamber above the damper has to guide smoke smoothly into the flue. When any of these parts wear out, you get smoke in the room, cold drafts all winter, or loose masonry falling into the fire. EliteFlue Chimney Services repairs fireplaces and dampers in homes across Brooklyn and nearby neighborhoods, from original parlor-floor fireplaces in brownstones to wood and gas inserts in older openings. Our certified technicians find the cause, explain it in plain terms, and fix it with as little mess in your home as possible.

Signs you need it

Most fireplace and damper problems give you warning before they become dangerous. If you notice any of the following, have the fireplace looked at before your next fire.

  • A smoky or creosote smell in the room, especially on humid days or when the heat comes on
  • Poor draft: smoke rolls out of the opening instead of rising up the flue
  • Brick flakes, crumbled mortar or other debris collecting in the firebox
  • White, chalky staining on the brick around or inside the fireplace, a sign that water is moving through the masonry
  • Water in the firebox after rain, or rust on the damper or grate
  • Scratching or chirping in the chimney, which usually means the damper or cap isn't closing off the flue
  • A damper that sticks, won't open all the way, or won't close and lets cold air in all winter

What's included

Every repair visit starts with an inspection, so we fix the cause and not just the symptom. Depending on what we find, the work can include:

  • Inspection of the firebox, damper, smoke chamber and visible flue
  • Repair or replacement of throat dampers that are warped, rusted or seized
  • Installation of top-sealing dampers that close at the top of the chimney and also keep out rain and animals
  • Replacement of cracked or missing firebrick and repointing of firebox joints with heat-rated refractory mortar
  • Smoke chamber parging to smooth rough, stepped brick that slows draft and traps creosote
  • Repair or replacement of the chimney cap and spark screen
  • Diagnosis of draft problems, including flue size, chimney height and air supply in the home
  • Cleaning of the firebox and flue where needed so repairs bond properly
  • Photos of the problem areas and a written summary of the work done

How our crew works in your home and on the roof

Inside, the crew lays drop cloths from the door to the hearth and covers the fireplace opening before any brushing or chipping starts. HEPA vacuums run during the work to capture soot and masonry dust at the source, so it doesn't settle on your floors or furniture. When the flue needs cleaning before a repair, we use rotary brushes that spin against the flue walls to break loose creosote and debris.

Some problems can't be seen from the firebox, such as cracks in the flue or gaps between liner sections. For those, we run a camera up the chimney and show you the footage. You see what we see, and your repair decisions are based on the actual condition of the flue.

On the roof, we check the crown, cap, flashing and the top of the flue. Brooklyn row houses and brownstones often have shared walls and tight roof access, so we plan the safest route up, whether through a bulkhead, a roof hatch or from outside the building. We protect roofing surfaces where we set ladders and tools. Top-sealing dampers and caps are installed from up there.

The standard we follow

We work to NFPA 211, the national standard for chimneys, fireplaces and vents. It calls for these systems to be inspected once a year, and it guides how our certified technicians evaluate and repair them.

Chimney professionals use three inspection levels. A Level 1 inspection fits when nothing about the system has changed. A Level 2 inspection applies when something changes, such as adding a new appliance or insert or switching fuel, and when a home is sold. A Level 3 inspection is for cases where a hidden hazard can only be reached by opening part of the chimney or the building. Most fireplace repairs begin with a Level 1 or Level 2 inspection, and we tell you which one fits and why before we start.

If your building is converting its boiler from oil to gas, New York City requires the chimney to be evaluated as part of that work. A new liner is often needed, because gas exhaust produces acidic condensate that can corrode a masonry flue. If your fireplace flue sits in the same chimney as the boiler flue, we can look at both on the same visit.

What affects the price

Every fireplace is different, so we quote after we've seen yours. The main factors are:

We go over the quote line by line with you before any work begins.

  • Chimney height and roof access, including whether we need extra ladders or a bulkhead route
  • Fuel type: wood-burning, gas logs, or a wood or gas insert
  • Flue size and condition, including whether it's lined, unlined or damaged
  • How much creosote, soot or debris has built up
  • Whether a camera inspection is needed to find the problem
  • The extent of the repair, from a single damper replacement to rebuilding firebox walls

How a visit works

You book a time that works for you, and we confirm the day before. When the technician arrives, they ask what you've noticed, set up floor protection, and inspect the fireplace, damper and chimney from inside and on the roof.

Next, we show you photos or camera footage, explain the problem in plain terms, and give you a written quote. Simple repairs, like freeing a stuck damper or replacing a cap, can often be done on the same visit. Larger masonry work is scheduled so the mortar can cure properly before you light a fire.

Before we leave, we vacuum, remove the drop cloths, and show you how to operate any new damper. Many owners book before fall, since things get busy once the city's heat season starts on October 1.

What to expect

How a visit goes

  1. We show you what we see

    Camera footage and photos of the flue, crown and firebox let you see the condition of your chimney for yourself instead of taking our word for it.

  2. We recommend only what is needed

    A dirty flue gets a sweep. A cracked crown gets a repair. We explain the difference between what is urgent and what can wait.

  3. We respect your home

    Drop cloths, sealed fireplace openings and HEPA vacuums keep soot and debris contained, and we leave the work area clean.

FAQ

Common questions

Can I use my fireplace if the damper is broken?

If the damper is stuck closed or only partly open, don't light a fire, because smoke and carbon monoxide can back up into the room. If it's stuck open, the fireplace may still draw, but you'll lose heat all winter. Have it checked before you use it.

What's the difference between a throat damper and a top-sealing damper?

A throat damper sits just above the firebox and is the original type in most older homes. A top-sealing damper mounts at the top of the chimney and is opened with a cable from the firebox. It seals tighter and also keeps out rain and animals.

Why is there white staining on my fireplace brick?

That chalky white residue is usually salts left behind as water moves through the masonry and evaporates. It means water is getting in somewhere, often through the crown, cap, flashing or brick. We find the entry point before repairing the fireplace itself.

Do you repair gas fireplaces and inserts?

Yes. We inspect and repair the firebox, damper, venting and chimney for gas log sets and for wood and gas inserts. Gas appliances need a properly sized and lined flue, so we check that as part of the visit.

How soon can I use the fireplace after a firebox repair?

It depends on the work. A damper or cap replacement usually doesn't require waiting. Firebrick and mortar repairs need time to cure, and your technician will tell you how long to wait before the first fire.

How often should my fireplace be inspected?

The NFPA 211 standard calls for chimneys, fireplaces and vents to be inspected once a year. An inspection is also a good idea if you change fuel, add an insert, or buy or sell a home.

Schedule a Chimney or Vent Inspection

Tell us what you are noticing and what kind of building you live in. We will inspect, show you what we find, and give you a written price before any work begins.

Call (912) 881-8281 Request Service