Skip to content
Serving Brooklyn and nearby cities Mon–Fri: 8 AM–8 PM · Requests accepted 24/7 · (912) 881-8281

Chimney Liner Installation in Brooklyn

Serving Brooklyn and nearby cities.

Tell us what’s going on

Prefer to talk? (912) 881-8281

The short answer

You likely need a new chimney liner if your existing liner is cracked or missing, if you notice smoke smells or poor draft, or if you are converting a boiler from oil to gas. EliteFlue inspects the flue with a camera, cleans it, sizes and installs a liner matched to your appliance, and follows the NFPA 211 standard throughout.

A chimney liner is the protective channel inside your flue that carries smoke and exhaust gases up and out of the house. It keeps heat away from the surrounding brick and wood framing, and it keeps corrosive byproducts from eating into the masonry. Many older Brooklyn row houses and brownstones have clay tile liners that have cracked or shifted over time, and some chimneys were never lined at all. EliteFlue Chimney Services installs new liners for fireplaces, wood stoves, inserts, and oil and gas heating appliances in Brooklyn and nearby neighborhoods. Our certified technicians start with an inspection, size the liner to the appliance it serves, and leave your home as clean as they found it.

Signs You Need a New Chimney Liner

A damaged liner sits out of sight inside the chimney, so homeowners usually notice the side effects first. If you see any of the following, schedule an inspection before you rely on the fireplace or heating system again.

The last item matters in New York City. When a building converts its boiler from oil to gas, the chimney has to be evaluated as part of the work, and a new liner is often needed. Gas exhaust produces acidic condensate that can corrode a masonry flue that handled oil without trouble.

  • A smoke or creosote smell in the room, especially on humid days or when the appliance is off
  • Poor draft: smoke rolling back into the room, or a stove that is hard to keep burning
  • Pieces of clay tile, mortar or brick flakes collecting in the firebox or at the base of the flue
  • White staining on the outside brick, a sign that moisture is moving through the masonry
  • Water in the firebox or rust on the damper after rain
  • A planned boiler conversion from oil to gas, or a new stove or insert going in

What Is Included in a Liner Installation

Every liner job follows the same core steps, adjusted to the appliance and the chimney it serves.

If we find damage a liner will not solve, such as a failing crown or deteriorated brick above the roofline, we explain what we found and give you options before doing any additional work.

  • Pre-installation inspection of the flue, including a camera scan of the interior
  • Cleaning of the flue with rotary brushes to remove soot, creosote and loose debris
  • Measurement of the flue and review of the appliance to size the liner correctly
  • Removal of broken clay tile or obstructions where needed for clearance
  • Installation of the new liner, typically stainless steel, from the top of the chimney down to the appliance connection
  • Insulation where the chimney and liner type call for it
  • Top plate and rain cap at the crown to keep out water and animals
  • Connection to the fireplace, stove, insert or boiler, followed by a draft check
  • Final camera review and a written summary with photos

How Our Crew Works Inside Your Home and on the Roof

Before any tools come out, the crew lays drop cloths from the entry door to the work area and seals off the fireplace or appliance opening. HEPA vacuums run during cleaning to capture soot at the source instead of letting it drift into the room. Rotary brushes clear the existing flue so the camera gives a clear picture and the new liner slides in without catching on buildup.

Most of the installation happens from the roof. The crew sets up safe access, which on attached row houses often means a roof hatch or bulkhead, then feeds the liner down from the top. Old tile is broken out only where it blocks the new liner. At the crown, the liner is secured with a top plate and capped. The crew protects roofing surfaces as they work and clears debris before leaving.

When the job is finished, we run the camera again so you can see the completed liner, then vacuum the work area and remove every drop cloth.

The Standard We Follow

Liner work is guided by NFPA 211, the national standard for chimneys, fireplaces and vents. It calls for these systems to be inspected once a year. Chimney professionals use three inspection levels to decide how deep that inspection goes.

Installing a liner, converting fuel or adding a new stove counts as a change to the system, so a Level 2 inspection is the usual starting point for liner work. We recommend a Level 3 inspection only when there is evidence of a problem that cannot be reached any other way.

  • Level 1: for a system where nothing has changed
  • Level 2: when the system changes, such as a new appliance or a switch of fuel, or when the home is sold
  • Level 3: when a hidden hazard has to be reached by opening part of the chimney or building

What Affects the Cost

Every chimney is different, so we quote after the inspection rather than guessing beforehand. These are the main factors:

We put the scope of work in writing so you know exactly what is included before the crew starts.

  • Chimney height and roof access, including whether the roof is reached by hatch, bulkhead or ladder
  • Fuel type and appliance, since wood, oil and gas each call for a suitable liner
  • Flue size, shape and condition, including whether old tile has to be removed
  • How much creosote or soot buildup has to be cleaned first
  • Whether a camera inspection, insulation or masonry repair is needed

How a Visit Works

You book an inspection at a time that works for you. The technician inspects the appliance and flue, shows you the camera footage, explains whether a liner is needed and which type fits, and gives you a written quote. Once you approve it, we schedule the installation and tell you how long the work should take.

If your chimney serves a boiler, it helps to plan liner work outside New York City's heat season, which runs from October 1 through May 31, when building owners must keep apartments heated to the city's minimum temperatures. If the work has to happen during that window, we coordinate with you to keep heating downtime as short as possible.

Chimney Liner Installation by city

What to expect

How a visit goes

  1. We show you what we see

    Camera footage and photos of the flue, crown and firebox let you see the condition of your chimney for yourself instead of taking our word for it.

  2. We recommend only what is needed

    A dirty flue gets a sweep. A cracked crown gets a repair. We explain the difference between what is urgent and what can wait.

  3. We respect your home

    Drop cloths, sealed fireplace openings and HEPA vacuums keep soot and debris contained, and we leave the work area clean.

FAQ

Common questions

Do I need a new liner if I am converting my boiler from oil to gas?

Often, yes. In New York City the chimney has to be evaluated as part of an oil-to-gas conversion, and a new liner is frequently needed because gas exhaust produces acidic condensate that can corrode a masonry flue.

How do I know if my current liner is damaged?

Common clues include smoke or creosote smells, poor draft, tile or brick flakes in the firebox, white staining on the brick, and water in the firebox. A camera inspection is the most reliable way to confirm the liner's condition.

What type of liner will you install?

Stainless steel is the most common choice because it can be sized to the appliance and fed down an existing flue. We recommend a type after inspecting the chimney and confirming the fuel and appliance it serves.

Will the installation make a mess inside my home?

We lay drop cloths from the door to the work area, seal the appliance opening, and run HEPA vacuums during cleaning. Most of the installation happens from the roof, and we clean up before we leave.

Can I use my fireplace or heating system during the work?

No. The appliance connected to the chimney has to stay off while the flue is cleaned and lined. We reconnect it and check the draft before we finish.

How often should the chimney be inspected after a new liner goes in?

The NFPA 211 standard calls for chimneys, fireplaces and vents to be inspected once a year, and that applies to a newly lined chimney as well.

Schedule a Chimney or Vent Inspection

Tell us what you are noticing and what kind of building you live in. We will inspect, show you what we find, and give you a written price before any work begins.

Call (912) 881-8281 Request Service