Skip to content
Serving Brooklyn and nearby cities Mon–Fri: 8 AM–8 PM · Requests accepted 24/7 · (912) 881-8281

Chimney Liner Installation in Downtown Brooklyn

Serving Downtown Brooklyn and nearby cities.

Tell us what’s going on

Prefer to talk? (912) 881-8281

The short answer

A chimney liner is a sealed channel inside your chimney that carries smoke or gas exhaust safely out of the house and keeps heat and acidic condensate away from the masonry. In Downtown Brooklyn, liners are most often needed when an older brick flue is damaged, when an appliance is replaced, or when a building converts its boiler from oil to gas.

Many chimneys in Downtown Brooklyn were built long before today's boilers, water heaters and wood inserts existed. Brownstones, rowhouses and pre-war apartment buildings around the 11201 ZIP code often have masonry flues that have cracked, lost mortar or were never sized for the appliance now venting through them. A properly sized chimney liner gives exhaust a sealed, continuous path out of the building and protects the masonry around it. EliteFlue Chimney Services is based in Fort Greene, about a mile south of Downtown Brooklyn, and our certified technicians install liners for homes and buildings throughout the neighborhood.

Why Older Brooklyn Chimneys Often Need a Liner

Older brick chimneys were commonly built with clay tile flues, and some have no lining at all. Over decades, freeze-thaw cycles, settling and constant heating seasons can crack tiles and wash out mortar joints. Cracks let heat, smoke and combustion gases reach brick, wood framing or neighboring spaces. In attached rowhouses and multi-unit buildings, that can affect more than one household.

A flue that is too large for the appliance it serves can also cause trouble. Exhaust cools as it rises, draft weakens, and moisture condenses on the inside walls. A liner sized to the appliance restores steady draft and keeps that moisture contained.

Oil-to-Gas Conversions and Your Chimney

When a New York City building converts its boiler from oil to gas, the chimney has to be evaluated as part of the work. A new liner is often needed because gas exhaust produces acidic condensate that can corrode a masonry flue over time.

If your building in Downtown Brooklyn is planning a conversion, it helps to bring us in early. We can inspect the existing flue, tell you what the new equipment will need, and coordinate with your heating contractor so the liner is ready when the boiler is.

Choosing the Right Liner

The right liner depends on the appliance, the fuel and the shape of the chimney. After inspecting the flue, we explain the options that fit your setup instead of offering one product for every job. Common choices include:

  • Stainless steel liners, rigid or flexible, which work with many wood, oil and gas appliances and can follow offsets in older chimneys
  • Liners sized specifically for a wood stove or fireplace insert, so the insert drafts properly
  • Liners matched to gas boilers and water heaters, built to handle acidic condensate
  • Insulation around the liner where needed, to keep exhaust warm and improve draft
  • Cast-in-place liners for some masonry chimneys that need structural reinforcement as well as a new flue

How Liner Installation Works

Every job starts with an inspection. The NFPA 211 standard describes three inspection levels, and a Level 2 inspection is the usual starting point when a system changes, such as a new appliance or a switch of fuel. It includes a camera look inside the flue so we can see cracks, gaps and obstructions that are not visible from the firebox or roof.

Once the plan is set, we clean the flue, run the liner down from the top of the chimney, connect it to the appliance, and seal and cap it at the top. We protect floors and furnishings in the work area and walk you through the finished installation, including camera images of the liner in place.

Timing Your Project Around the Heating Season

New York City's heat season runs from October 1 through May 31, and building owners must keep apartments heated to the city's minimum temperatures during that time. For multi-unit buildings, that makes late spring and summer the easiest time to replace a liner on a boiler flue, because the system can be down without leaving tenants cold.

Problems do not always wait for summer, though. If a boiler or water heater is showing venting trouble in winter, we work to schedule promptly. We also serve nearby DUMBO, Boerum Hill, Brooklyn Heights, Fort Greene and Clinton Hill.

More services in Downtown Brooklyn

Related

What to expect

How a visit goes

  1. We show you what we see

    Camera footage and photos of the flue, crown and firebox let you see the condition of your chimney for yourself instead of taking our word for it.

  2. We recommend only what is needed

    A dirty flue gets a sweep. A cracked crown gets a repair. We explain the difference between what is urgent and what can wait.

  3. We respect your home

    Drop cloths, sealed fireplace openings and HEPA vacuums keep soot and debris contained, and we leave the work area clean.

FAQ

Common questions

How do I know if my chimney needs a liner?

Common signs include cracked or missing flue tiles, crumbling mortar inside the chimney, stains or dampness on walls near the chimney, poor draft, and a recent change of appliance or fuel. An inspection with a camera is the reliable way to know.

Do I need a new liner if my building is switching from oil to gas?

The chimney has to be evaluated as part of a New York City oil-to-gas conversion, and a new liner is often needed because gas exhaust produces acidic condensate that can corrode a masonry flue.

Can a liner be installed in a chimney that bends?

Often, yes. Flexible stainless steel liners can follow offsets that are common in older brownstones and rowhouses. We confirm the route during the inspection.

How long does liner installation take?

Many single-flue installations are completed in a day once materials are ready. Larger buildings, tall chimneys or jobs that need masonry repair can take longer, and we tell you what to expect after the inspection.

Will I need an inspection after the liner is installed?

The NFPA 211 standard calls for chimneys, fireplaces and vents to be inspected once a year. A yearly check keeps an eye on the liner, cap and connections.

Do you install liners for fireplaces and wood stove inserts?

Yes. We size and install liners for wood-burning inserts and stoves as well as for gas and oil heating equipment.

Schedule a Chimney or Vent Inspection

Tell us what you are noticing and what kind of building you live in. We will inspect, show you what we find, and give you a written price before any work begins.

Call (912) 881-8281 Request Service