The short answer
A DUMBO chimney usually needs a new liner when clay flue tiles crack, a boiler converts from oil to gas, or a new heating appliance is installed. EliteFlue inspects the flue, sizes a liner to your equipment and installs it from our Fort Greene base about a mile away.
A chimney liner is the protective channel inside a flue. It carries smoke and exhaust out of the building and keeps heat and corrosive byproducts away from the surrounding masonry. In DUMBO, many people live in converted loft buildings, pre-war apartment buildings and older rowhouses. In these buildings, liner work usually comes up during a boiler conversion, a fireplace restoration, or an inspection that finds cracked clay tiles. EliteFlue installs chimney liners throughout DUMBO from our office in Fort Greene, about a mile away. We size each liner to the specific appliance it serves.
When a DUMBO Chimney Needs a New Liner
Older masonry chimneys in the neighborhood were often built with clay tile liners, and some have no liner at all. Over decades, heating cycles, water entry and building settling can crack tiles or open the mortar joints between them. A damaged liner lets heat and exhaust reach brick and wood framing. It can also let combustion gases leak into living space. These are the most common signs that a liner needs attention:
- Cracked, shifted or missing clay flue tiles found during an inspection
- A new boiler, water heater or furnace that the existing flue was not sized for
- A switch from oil to gas heat
- Brown staining, flaking brick or damp patches on walls next to the chimney
- Plans to bring an unused fireplace back into service
Oil-to-Gas Conversions and Liners in NYC Buildings
When a New York City building converts its boiler from oil to gas, the chimney has to be evaluated as part of the work. A new liner is often needed. Gas exhaust produces acidic condensate, and over time that moisture can corrode a masonry flue that was built for oil.
For owners of rowhouses and smaller multifamily buildings, we coordinate with your heating contractor so the liner matches the new equipment's size and exhaust type. Installing the liner at the same time as the boiler swap means you won't have to open the chimney again later.
Matching the Liner to the Appliance
No single liner fits every chimney. The right choice depends on what the flue serves, the size of the opening, and the shape and condition of the masonry. Common options include:
Size matters as much as material. An oversized flue can cause weak draft and condensation, and an undersized one can push exhaust back into the room. We measure the flue and check the appliance's venting needs before recommending anything.
- Stainless steel liners for gas and oil appliances, sized to the appliance's venting requirements
- Insulated stainless liners for wood-burning fireplaces and stoves, which run at higher temperatures
- Rigid or flexible sections, depending on whether the flue runs straight or has offsets
- A proper cap at the top and a sealed connection at the base
How Liner Installation Works
The NFPA 211 standard calls for chimneys to be inspected once a year. It treats a change to the system, such as new equipment or a switch of fuel, as a reason for a more thorough Level 2 inspection. That inspection usually includes a camera look inside the flue, and liner work starts from what it shows. The installation itself follows these steps:
In loft and apartment buildings, we plan roof access ahead of time. We also protect shared hallways and finished interiors before any work begins.
- Inspect the flue and record its condition with camera footage
- Clean the chimney so the new liner goes into a clear passage
- Measure the flue and confirm the appliance's venting requirements
- Install the liner from the top, connect it at the base and fit a cap
- Check the draft and walk you through what was done
Planning Around Heat Season
New York City's heat season runs from October 1 through May 31. During that period, building owners must keep apartments heated to the city's minimum temperatures. If your building's boiler vents through a chimney that needs relining, scheduling the work in late spring or summer keeps the heat on while tenants rely on it. If a problem turns up in the middle of winter, our certified technicians can assess the flue quickly and help you decide on next steps.
Serving DUMBO and Nearby Brooklyn Neighborhoods
Our Fort Greene office is about a mile from DUMBO, so we can get there easily for inspections and liner installations anywhere in the 11201 ZIP code. We also install chimney liners in Downtown Brooklyn, Boerum Hill, Brooklyn Heights, Fort Greene and Clinton Hill. Brownstones, rowhouses and pre-war buildings in those neighborhoods share many of the same flue problems.
More services in DUMBO
- Chimney Sweep in DUMBO
- Chimney Inspection in DUMBO
- Chimney Repair in DUMBO
- Air Duct Cleaning in DUMBO
