Skip to content
Serving Brooklyn and nearby cities Mon–Fri: 8 AM–8 PM · Requests accepted 24/7 · (912) 881-8281

Chimney Liner Installation in Park Slope, Brooklyn

Serving Park Slope and nearby cities.

Tell us what’s going on

Prefer to talk? (912) 881-8281

The short answer

You likely need a new chimney liner in Park Slope if your flue is cracked, unlined, or now serves a different appliance or fuel, especially after an oil-to-gas boiler conversion. EliteFlue starts with a camera inspection, then sizes and installs a liner that fits your appliance and your chimney's shape.

Many Park Slope homes were built long before modern heating equipment, and their chimneys were often finished with clay tile flues or bare brick. Over time those flues crack, shift or wear away, and newer boilers and water heaters vent differently than the equipment they replaced. EliteFlue Chimney Services installs chimney liners in brownstones, rowhouses and pre-war apartment buildings across Park Slope, about a mile south of our Fort Greene office. Here is what a liner does, when you may need one, and how the work usually goes in a Park Slope home.

Why Liners Matter in Park Slope's Older Homes

A liner is the channel inside the chimney that carries smoke or exhaust up and out of the house. It keeps heat and combustion gases away from the surrounding brick and wood framing, and it gives the flue the right size and shape for the appliance it serves.

In a neighborhood of attached brownstones and rowhouses, a chimney often runs through a shared or party wall and passes several floors of living space on its way to the roof. A cracked or missing liner can let exhaust seep into rooms or into the wall itself. In attached buildings, a flue problem may not stay inside one home.

Older flues were also sized for the equipment of their day. A modern high-efficiency boiler or water heater may produce cooler exhaust that does not draft well in a large old flue, which is another reason a properly sized liner matters.

Signs Your Flue May Need a Liner

Some problems are easy to spot, but many are only found when a technician looks inside the flue with a camera. Call us if any of these apply to your home:

  • Your building has converted, or plans to convert, its boiler from oil to gas
  • A new boiler, furnace or water heater now vents into an old masonry flue
  • A past inspection found cracked, missing or displaced clay tiles
  • Pieces of tile, mortar or brick are collecting at the base of the chimney or in the cleanout
  • Water stains, flaking paint or white staining appear on walls near the chimney
  • You want to start using a fireplace that has sat unused for years

Oil-to-Gas Conversions and Your Chimney

Many Park Slope buildings have switched, or are switching, from oil heat to gas. When a New York City building converts its boiler from oil to gas, the chimney has to be evaluated as part of the work. A new liner is often needed, because gas exhaust produces acidic condensate that can corrode a masonry flue that was built for oil.

We can coordinate with your heating contractor so the liner is sized for the new equipment and installed on a schedule that fits the conversion. Timing matters here: New York City's heat season runs from October 1 through May 31, when building owners must keep apartments heated to the city's minimum temperatures. Many owners plan liner work so the heating system is not out of service during that stretch.

How We Install a Chimney Liner

Every job starts with an inspection. The NFPA 211 standard calls for chimneys to be inspected once a year, and it describes a Level 2 inspection when the system changes, such as a new appliance or a switch of fuel. That level includes a video scan of the flue, so we can see its real condition before recommending anything.

Stainless steel liners are common for gas and oil appliances and work well in the narrow or bent flues often found in older rowhouses. For wood-burning fireplaces, the right choice depends on the flue size and condition, and we explain the options before any work begins. A typical installation follows these steps:

  • Inspect and measure the flue, including any bends or offsets
  • Recommend a liner type and size that matches the appliance and fuel
  • Clean the flue and clear loose debris before installation
  • Run the liner from the roof, connect it at the appliance, and seal the top with a cap
  • Review the finished work with you, including photos or video of the flue

Serving Park Slope and Nearby Neighborhoods

Our certified technicians work throughout Park Slope, ZIP code 11217, along with nearby Prospect Heights, Carroll Gardens, Cobble Hill, Gowanus and Red Hook. Because our office is close by in Fort Greene, follow-up visits and annual inspections are simple to schedule.

Working on attached homes means planning roof access, protecting stair runners and interior finishes, and keeping neighbors in mind. We account for all of that when we schedule your visit, and we keep you informed about what we are doing at each stage.

More services in Park Slope

Related

What to expect

How a visit goes

  1. We show you what we see

    Camera footage and photos of the flue, crown and firebox let you see the condition of your chimney for yourself instead of taking our word for it.

  2. We recommend only what is needed

    A dirty flue gets a sweep. A cracked crown gets a repair. We explain the difference between what is urgent and what can wait.

  3. We respect your home

    Drop cloths, sealed fireplace openings and HEPA vacuums keep soot and debris contained, and we leave the work area clean.

FAQ

Common questions

How do I know if my Park Slope chimney needs a new liner?

The surest way is a camera inspection of the flue. Cracked tiles, missing sections, debris at the base, moisture stains near the chimney, or a recent change in heating equipment are all reasons to have it checked.

Do I need a liner if my building is converting from oil to gas?

Often, yes. New York City requires the chimney to be evaluated during an oil-to-gas boiler conversion, and a new liner is frequently needed because gas exhaust creates acidic condensate that can corrode a masonry flue.

What type of liner do you install?

Stainless steel liners are common for gas and oil appliances and fit well in narrow or bent flues. For wood-burning fireplaces, we recommend an option based on the flue's size and condition after inspection.

When is the best time to schedule liner installation?

Many building owners plan the work outside New York City's heat season, which runs from October 1 through May 31, so the heating system is not out of service while apartments must be kept warm.

Does the work happen inside my home?

Most of the installation is done from the roof, with a connection made at the appliance indoors. We protect floors and finishes along the path we use and clean up when the job is done.

Do you serve neighborhoods near Park Slope?

Yes. Along with Park Slope, we install liners in Prospect Heights, Carroll Gardens, Cobble Hill, Gowanus and Red Hook.

Schedule a Chimney or Vent Inspection

Tell us what you are noticing and what kind of building you live in. We will inspect, show you what we find, and give you a written price before any work begins.

Call (912) 881-8281 Request Service